Screw-topped Hollow Form

Monday 9 July 2018

There are certain times when you want to make a hollow form with a screw top. This can either by as a purely aesthetic piece – such as a cookie jar, for example – or it can also be used as an urn for holding ashes. In this sense, this design is also suitable as a vessel for holding pet ashes, if you have sadly lost a pet. For this reason, this screw-topped hollow form is very multi-functional. In this article I will tackle the issue of turning screw threads in particular, as well as the other steps involved in creating this piece, such as hollowing.

Shaping the external form

Step 1

Any timber will be fine for this project, but I had a 300 x 200mm (11 x 8in) piece of wet Spanish olivewood which I chose to use for its aesthetic appeal. When you place between centres, ensure that the pith is off-centre as from here cracks can originate. I turn the pith away in the piece and drill it out and fill it in the base

Step 2

Here I am using the tailstock end as the base and so, therefore, I need to square the end with pull cuts of my swept-wing bowl gouge, then I make a suitably sized spigot to hold in my largest chuck jaws

Step 3

When I first started to turn wood, I must have been slow on the uptake and it was some time before I realised that it is easier to cut from the outside of the tree in, and not along the length. Next, I rough shape the outside with my bowl gouge

Step 4

I have now turned the timber, holding it in the chuck so that I can concentrate on the overall shape. I use pull cuts for the main shaping and a push cut with my spindle gouge for the refining cuts

Step 5

I use a large SAD (Seasonal Affected Syndrome) bulb as the light is the equivalent to daylight and shows blemishes and defects better than any other light I have used

Step 6

For the final cut, I use a freshly sharpened shear-scraping finishing tool which normally leaves a beautiful blemish free surface

Hollowing and chasing threads

Step 7

To start the hollowing, I always drill down to the required depth using a 12mm (1/2in) drill bit, drilling short sections at a time. When completed, it is time to consider the hollowing…

Step 8

…using a 12mm (1/2in) spindle gouge followed by the Proforme Hollowing Tool. I open the neck up to allow a collar of dense material African blackwood, in this case, to be fitted…

Step 9

The collar will now fit snugly into the opening of the hollow form and makes a wonderful thread

Step 10

Fit the blackwood collar and chase an internal thread using whichever tpi chasers you feel confident with

Step 11

You can now finish hollowing the piece out. If this is to be an item to use rather than display, keep the wall thickness to about 6mm (1/4in)

Step 12

Once hollowed, you can now apply your preferred finish. Ensure not to finish the neck where the collar will be glued

Dealing with the base

Step 13

Remembering to part upwards to form a convex base, part off to 10mm (3/8in) Then, saw the remaining spigot off flush with the piece. On the remaining base, make the remaining 10mm (3/8in)) piece into a short spigot

Step 14

The pith is off-centre and we can now drill it through by using a 10mm (3/8in) drill bit

Step 15

A part of the 10mm (3/8in) spigot from the base now glues perfectly into the hole where the pith was. The base now just needs sanding and finishing

Thread chasing

Step 16

Using the remaining blackwood, turn a spigot to thread into the collar made earlier. Use the same tpi size thread chasers as before

Step 17

Once the thread is cut, shape the rest of the lid. Continue to shape the finial as far as possible while it is still held in the chuck

Step 18

Once the lid is shaped, turn the finial round and hold it in a sacrificial threaded recess. Shape, sand and finish as required. The hollow form with blackwood collar is now complete

Alternative threading method

For those who do not know how to thread chase and want to use an alternative, here is a trick gleaned from the Internet. The trick is to use plastic plumbing fittings to replace threads cut earlier. The cost worked out at a very reasonable £4. Some may see this as cheating, but I think it’s more a case of working to our strengths rather than getting frustrated with something that can be solved in another way, or using another method.

I know many have tried and struggled with thread chasing – if it is a subject that fascinates you then persevere and repetition will yield results. If it is of passing interest, maybe one project every year or so, then the time spent learning it is time that can be spent on other things you enjoy making.

Step 1

Plastic to male iron connector from our local plumbing merchants turned down so that…

Step 2

…the female section fits into the hollow form and the male section forms part of the lid

Step 3

There is a small recess at the side into which the rim where the plastic insert sits. I will make the plastic insert shorter then glue it in place

Step 4

If using the plumbing insert, make a hole in the wood left (the lid) in the chuck to fit the male plastic thread perfectly

Step 5

Remove the thread part, turn the wood around and expand the jaws into the hole you have just made. Now, turn the top and then sand and finish as required and glue in the insert

Step 6

An alternate design using plastic plumbing parts for the threads